Horstbox DVA-G3342SB with FreeBSD

[Michael Fuckner]

Hi,

I am trying to boot FreeBSD on a Horstbox Professional made by Dlink.

I used the instructions from http://wiki.freebsd.org/FreeBSDAvila


- Do I still need npe-firmware or does FreeBSD simply use the one 
uuencoded in the source tree?
- where do I get information about the memory regions used in kernel 
configuration

options         PHYSADDR=0x10000000
options         KERNPHYSADDR=0x10200000
options         KERNVIRTADDR=0xc0200000         # Used in ldscript.arm
options         FLASHADDR=0x50000000
options         LOADERRAMADDR=0x00000000

Long version with all details is at 
http://michael.fuckner.net/me/blog/index.php?/archives/420-Horstbox-DVA-G3342SB-with-FreeBSD.html#extended

TIA,
  Michael!

PS: This is what happenes right now:
The Kernel boots, but in the middle, the system simply hangs.

RedBoot> load -b 0x200000 kernel-horst.nfs
Using default protocol (TFTP)
Address offset = 0x40000000
Entry point: 0x00200100, address range: 0x00200000-0x0054e330
RedBoot> go
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-STABLE #1: Wed May 14 07:24:11 CEST 2008
     root at g33.rebootking.de:/usr/obj/arm/samba/freebsd7-arm/src/sys/HORST
CPU: IXP425 533MHz rev 1 (ARMv5TE) (XScale core)
   DC enabled IC enabled WB enabled LABT branch prediction enabled
   32KB/32B 32-way Instruction cache
   32KB/32B 32-way write-back-locking Data cache
real memory  = 67108864 (64 MB)
avail memory = 58355712 (55 MB)
ixp0: <Intel IXP425> on motherboard
pcib0: <IXP425 PCI Bus> on ixp0
pci0: <PCI bus> on pcib0
ixppcib: no mapping for 0/12/0
ixppcib: no mapping for 0/13/0
ixppcib: no mapping for 0/14/0
ixppcib: no mapping for 0/14/1
ixppcib: no mapping for 0/14/2
pci0: <network> at device 12.0 (no driver attached)
pci0: <network> at device 13.0 (no driver attached)
ohci0: <NEC uPD 9210 USB controller> irq -1 at device 14.0 on pci0
ixppcib: no mapping for 0/14/0
ohci0: Could not allocate irq
pcib0: ohci0 called release_resource
device_attach: ohci0 attach returned 6
ohci1: <NEC uPD 9210 USB controller> irq -1 at device 14.1 on pci0
ixppcib: no mapping for 0/14/1
ohci1: Could not allocate irq
pcib0: ohci1 called release_resource
device_attach: ohci1 attach returned 6
ehci0: <NEC uPD 720100 USB 2.0 controller> mem 0x48002200-0x480022ff irq 
-1 at device 14.2 on pci0
pcib0: ehci0 called activate_resource
ehci0: Could not map memory
device_attach: ehci0 attach returned 6
ixpclk0: <IXP425 Timer> on ixp0
ixpiic0: <IXP425 GPIO-Based I2C Interface> on ixp0
iicbb0: <I2C bit-banging driver> on ixpiic0
iicbus0: <Philips I2C bus> on iicbb0 master-only
iicbus0: <unknown card> at addr 0
iic0: <I2C generic I/O> on iicbus0
ad74180: <Analog Devices AD7418 ADC> at addr 0x50 on iicbus0
ds16720: <Dallas Semiconductor DS1672 RTC> at addr 0xd0 on iicbus0
ixpwdog0: <IXP425 Watchdog Timer> on ixp0
uart0: <Non-standard ns8250 class UART with FIFOs> on ixp0
uart0: [FILTER]
uart0: console (115200,n,8,1)
uart1: <Non-standard ns8250 class UART with FIFOs> on ixp0
uart1: [FILTER]