Alpha PWS 433au (MiataGL) halts when booting installation CD,
with "halt code = 5"
Tim McIntosh
tmcintos at avalon.net
Wed Jan 17 06:54:30 UTC 2007
Hi,
This problem has been reported by others numerous times over the last
couple years; this is just a reminder that it still exists in 6.2R.
It would be great if somebody could address the issue.
This system has no PCI cards installed and no SCSI devices
installed. The HDD is on IDE0 and the CDROM is on IDE1.
I'm guessing the issue described in the following post may be the
cause of the problem? http://lists.freebsd.org/pipermail/freebsd-
alpha/2005-April/002294.html
The thing is, the QLogic SCSI controller is built-in on this system,
so there's no way to put it in front of the PCI-PCI bridge. Is there
any way to disable it, or disable the device driver, as a work-around?
Thanks!
Tim
Console output:
------------------------------
[Note that there is a delay of several seconds between the output of
"isp0: [GIANT-LOCKED]" and "halted CPU 0".]
>>>boot dkb0
System will be reset prior to boot.
*** keyboard not plugged in ...
ff.fe.fd.fc.fb.fa.f9.f8.f7.f6.f5.CPU 0 speed is 2.31 ns (433MHz)
Digital Personal WorkStation 433au5.e4.
Console V7.2-1 Mar 6 2000 14:47:02
CPU 0 booting
(boot dkb0.0.0.207.0 -flags A)
block 0 of dkb0.0.0.207.0 is a valid boot block
reading 411 blocks from dkb0.0.0.207.0
bootstrap code read in
base = 1d8000, image_start = 0, image_bytes = 33600
initializing HWRPB at 2000
initializing page table at 1ca000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Consoles: SRM firmware console
VMS PAL rev: 0x1000000010114
OSF PAL rev: 0x1000000020116
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM CD9660 boot, Revision 1.2
(root at ds10.freebie.xs4all.nl, Fri Jan 12 17:01:15 UTC 2007)
Memory: 65536 k
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x6fed50+0x39a70 syms=[0x8+0x76578+0x8+0x61c05]
-
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Entering /boot/kernel/kernel at 0xfffffc00003523b0...
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE #0: Sat Jan 13 02:32:39 UTC 2007
root at ds10.freebie.xs4all.nl:/usr/obj/usr/src/sys/GENERIC
Digital Personal Workstation (Miata)
Digital Personal WorkStation 433au, 432MHz
8192 byte page size, 1 processor.
CPU: EV56 (21164A) major=7 minor=0 extensions=0x1<BWX>
OSF PAL rev: 0x1000000020116
real memory = 65167360 (62 MB)
avail memory = 48701440 (46 MB)
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
RF5413, REGO)
cia0: <2117x Core Logic chipset>
cia0: Pyxis, pass 1
cia0: extended capabilities: 1<BWEN>
pcib0: <2117x PCI host bus adapter> on cia0
pci0: <PCI bus> on pcib0
dc0: <Intel 21143 10/100BaseTX> port 0x9000-0x907f mem
0x80151000-0x8015107f ir0
miibus0: <MII bus> on dc0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc0: Ethernet address: 00:00:f8:76:38:9d
dc0: interrupting at CIA irq 0
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Cypress 82C693 ATA controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x30
ata0: <ATA channel 0> on atapci0
ata0: interrupting at ISA irq 14
ata1: <ATA channel 1> on atapci0
ata1: interrupting at ISA irq 15
atapci1: <GENERIC ATA controller> port 0x170-0x177,0x374-0x377 mem
0x80140000-00
atapci1: unable to map interrupt
device_attach: atapci1 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0x80150000-0x80150fff irq
234 at dev0
ohci0: interrupting at ISA irq 10
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1080) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pcib1: <PCI-PCI bridge> at device 20.0 on pci0
pci1: <PCI bus> on pcib1
isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x8000-0x80ff mem
0x800100001
isp0: interrupting at CIA irq 3
isp0: [GIANT-LOCKED]
halted CPU 0
halt code = 5
HALT instruction executed
PC = 0
CPU 0 booting
System will be reset prior to boot.
*** keyboard not plugged in ...
ff.fe.fd.fc.fb.fa.f9.f8.f7.f6.f5.CPU 0 speed is 2.31 ns (433MHz)
Digital Personal WorkStation 433au5.e4.
Console V7.2-1 Mar 6 2000 14:47:02
CPU 0 booting
(boot dkc0.0.0.1004.0 -flags A)
failed to open dkc0.0.0.1004.0
>>>show config
Firmware
SRM Console: V7.2-1 Mar 6 2000 14:47:02
ARC Console: 5.70
PALcode: OpenVMS PALcode V1.20-16, Tru64 UNIX PALcode V1.22-18
SROM Version: v5.90
Processor
DECchip (tm) 21164A-2 Pass 433 MHz 96 KBytes SCache
0 MB BCache
PYXIS ASIC Pass 257
MEMORY
Memory Size = 64Mb
Bank Size/Sets Base Addr
------ ---------- ---------
0 64Mb 00000000
BCache Size = 0Mb
Tested Memory = 64Mbytes
PCI Bus
Bus 00 Slot 03: Digital Semiconductor 21143 Network Controller
ewa0.0.0.3.0 00-00-
F8-76-38-9D
Bus 00 Slot 07: Cypress PCI Peripheral Controller
Bus 00 Slot 07: Function 1: PCI IDE
dka0.0.0.107.0 Maxtor 9
0422D2
Bus 00 Slot 07: Function 2: PCI IDE
dkb0.0.0.207.0 Pioneer CD-
ROM ATAPI
Bus 00 Slot 07: PCI USB
Bus 00 Slot 20: DECchip 21152 PCI to PCI Bridge
Bus 01 Slot 04: ISP1040 Scsi Controller
pkc0.7.0.1004.0 SCSI Bus ID 7
ISA
Slot Device Name Type Enabled BaseAddr
IRQ DMA
0
0 MOUSE Embedded Yes 60 12
1 KBD Embedded Yes 60 1
2 COM1 Embedded Yes 3f8 4
3 COM2 Embedded Yes 2f8 3
4 LPT1 Embedded Yes 3bc 7
5 FLOPPY Embedded Yes 3f0
6 2
6 EIDE Embedded Yes 1f0 14
3f6 15
170
376
7 ES1888 Embedded Yes 220
5 1
5
8 USB Embedded Yes 10
>>>
More information about the freebsd-alpha
mailing list