AS1200 Question

[sp4rc]

> > has anyone been able to install FreeBSd 5.4 on a Alpha Server 1200? The
> > bootprocess from cd hangs.
> 
> An AS1200 should run just fine.
> At which point does it hang?
> Complete boot messages would be great.

oh, sorry for that, after 17h infront of my terminal i became a bit
forgetfully.

P00>>>boot dka500
Initializing...
  
 SROM V3.0 on cpu0
XSROM V6.0 on cpu0
BCache testing complete on cpu0
mem_pair0 -  256 MB 
mem_pair1 -  256 MB 
mem_pair2 -  256 MB 
mem_pair3 -  256 MB 
mem_pair4 -  256 MB 
mem_pair5 -  256 MB 
20..21..23..
please wait 54 seconds for T24 to complete
24..
Memory testing complete on cpu0
starting console on CPU 0
sizing memory
  0    256 MB DIMM
  1    256 MB DIMM
  2    256 MB DIMM
  3    256 MB DIMM
  4    256 MB DIMM
  5    256 MB DIMM
probing IOD1 hose 1 
  bus 0 slot 1 - NCR 53C810
  bus 0 slot 4 - QLogic ISP10X0
probing IOD0 hose 0 
PCI device in hose 0 slot 2 incorrectly decodes Type 1 configuration
cycles,
may interfere with subordinate PCI buses.
  bus 0 slot 1 - PCEB
    probing EISA Bridge, bus 1
  bus 0 slot 2 - Digital 2T-PMPAA/Pixelwork
  bus 0 slot 4 - DECchip 21140-AA
mouse test 4 failed
configuring I/O adapters...
  ncr0, hose 1, bus 0, slot 1
  isp0, hose 1, bus 0, slot 4
  floppy0, hose 0, bus 1, slot 0
  tulip0, hose 0, bus 0, slot 4
System temperature is 24 degrees C

AlphaServer 1200 Console V6.0-4, 10-MAY-2001 10:11:42

CPU 0 booting

(boot dka500.5.0.1.1 -flags a)
block 0 of dka500.5.0.1.1 is a valid boot block
reading 410 blocks from dka500.5.0.1.1
bootstrap code read in
Building FRU table
base = 200000, image_start = 0, image_bytes = 33400
initializing HWRPB at 2000
initializing page table at 1f2000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Console: SRM firmware console
VMS PAL rev: 0x4000200010115
OSF PAL rev: 0x4000200020117
Switch to OSF PAL code succeeded.

FreeBSD/alpha SRM CD9660 boot, Revision 1.2
(root at ds10.freebie.xs4all.nl, Mon May  9 13:32:23 UTC 2005)
Memory: 1572864 k
Loading /boot/defaults/loader.conf 
/boot/kernel/kernel data=0x5e8d60+0x3d720 syms=[0x8+0x669a8+0x8+0x54f0f]
\
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...               
Entering /boot/kernel/kernel at 0xfffffc0000345de0...
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights
reserved.
FreeBSD 5.4-RELEASE #0: Mon May  9 21:18:39 UTC 2005
    root at ds10.freebie.xs4all.nl:/usr/obj/usr/src/sys/GENERIC

never mind about the -a flag, i have also tried without it...

any hints would be greatly appreciated.

/sp4rc