FreeBSD 5.3-BETA1 boot OK on Alpha Server 2100 5/250RM
Gheorghe Ardelean
ardelean at ww.uni-erlangen.de
Tue Aug 31 06:22:01 PDT 2004
Hi,
Today I have tested my Alpha Server at work and to my surprise the BETA1
disc was booting ok on this machine.
Thank you Andrew for supporting this machine in FreeBSD (IIRC he wrote
the support for this)!
The graphic card is a Compaq Qvision in an EISA slot!
The config and boot mesage (boot -v) follows!
Regards,
G. Ardelean
==========
VMS PALcode V1.20-3, OSF PALcode V1.22-1
starting console on CPU 0
Testing Memory bank 0
Testing Memory bank 1
Testing Memory bank 2
Testing Memory bank 3
Configuring Memory Modules
probing hose 0, PCI
probing PCI-to-EISA bridge, bus 1
bus 0, slot 0 -- ewa -- DECchip 21040-AA
bus 0, slot 1 -- pka -- NCR 53C810
bus 1, slot 2 -- vga -- Compaq Qvision
** keyboard error **
starting console on CPU 1
starting console on CPU 2
starting console on CPU 3
os_type: UNIX - console CIPCA driver not started
Memory Testing and Configuration Status
Module Size Base Addr Intlv Mode Intlv Unit Status
------ ----- --------- ---------- ---------- ------
2 512MB 00000000 2-Way 0 Passed
3 512MB 00000000 2-Way 1 Passed
Total Bad Pages 0
Testing the System
Testing the Disks (read only)
Testing the Network
AlphaServer 2100 Console V5.3-6, built on Oct 16 1998 at 12:49:45
P00>>>show dev
dka0.0.0.1.0 DKA0 RZ28 442D
dka100.1.0.1.0 DKA100 RZ28 D41C
dka200.2.0.1.0 DKA200 RZ28 442D
dka300.3.0.1.0 DKA300 RZ28 442D
dka600.6.0.1.0 DKA600 RRD43 1084
dva0.0.0.1000.0 DVA0 RX26/RX23
ewa0.0.0.0.0 EWA0 08-00-2B-E2-78-1C
pka0.7.0.1.0 PKA0 SCSI Bus ID 7
P00>>>show config
Digital Equipment Corporation
AlphaServer 2100 5/250
SRM Console V5.3-6 VMS PALcode V1.20-3, OSF PALcode V1.22-1
Component Status Module ID
CPU 0 P B2040-AA DECchip (tm) 21164-1
CPU 1 P B2040-AA DECchip (tm) 21164-1
CPU 2 P B2040-AA DECchip (tm) 21164-1
CPU 3 P B2040-AA DECchip (tm) 21164-1
Memory 2 P B2022-CA 512 MB
Memory 3 P B2022-CA 512 MB
I/O B2110-AA
dva0.0.0.1000.0 RX26/RX23
Slot Option Hose 0, Bus 0, PCI
0 DECchip 21040-AA ewa0.0.0.0.0 08-00-2B-E2-78-1C
1 NCR 53C810 pka0.7.0.1.0 SCSI Bus ID 7
dka0.0.0.1.0 RZ28
dka100.1.0.1.0 RZ28
dka200.2.0.1.0 RZ28
dka300.3.0.1.0 RZ28
dka600.6.0.1.0 RRD43
2 Intel 82375 Bridge to Bus 1, EISA
Slot Option Hose 0, Bus 1, EISA
2 Compaq Qvision
P00>>>
P00>>>boot dka600
(boot dka600.6.0.1.0 -flags A)
block 0 of dka600.6.0.1.0 is a valid boot block
reading 409 blocks from dka600.6.0.1.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 33200
initializing HWRPB at 2000
initializing page table at 3fff0000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Console: SRM firmware console
VMS PAL rev: 0x4000300010114
OSF PAL rev: 0x4000100020116
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM CD9660 boot, Revision 1.2
(root at ds10.wbnet, Mon Aug 23 08:53:04 UTC 2004)
Memory: 1048576 k
Loading /boot/defaults/loader.conf
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel] in 9 seconds...
Type '?' for a list of commands, 'help' for more detailed help.
OK boot -v
Entering /boot/kernel/kernel at 0xfffffc0000347100...
GDB: debug ports: sio
GDB: current port: sio
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-BETA1 #0: Mon Aug 23 22:50:09 UTC 2004
root at ds10.wbnet:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xfffffc0000e02000.
Preloaded mfs_root "/boot/mfsroot" at 0xfffffc0000e020e0.
DEC AlphaServer 2100
AlphaServer 2100 5/250, 250MHz
8192 byte page size, 4 processors.
CPU: EV5 (21164) major=5 minor=1
OSF PAL rev: 0x4000100020116
real memory = 1071570944 (1021 MB)
Physical memory chunk(s):
0x00e24000 - 0x3f0c9fff, 1042964480 bytes (127315 pages)
avail memory = 1036075008 (988 MB)
smp_start_secondary: starting cpu 1
smp_start_secondary: cpu 1 started
smp_start_secondary: starting cpu 2
smp_start_secondary: cpu 2 started
smp_start_secondary: starting cpu 3
smp_start_secondary: cpu 3 started
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
mem: <memory>
t20: using interrupt type 0 on pci bus 0
t20: <T2 Core Logic chipset>
pcib0: <T2 PCI host bus adapter> on t20
pci0: <PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 4, range 32, base 00010100, size 7, enabled
map[14]: type 1, range 32, base 81000100, size 7, enabled
found-> vendor=0x1011, dev=0x0002, revid=0x23
bus=0, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0xff (7650 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=2
map[10]: type 4, range 32, base 00010000, size 8, enabled
map[14]: type 1, range 32, base 81000000, size 8, enabled
found-> vendor=0x1000, dev=0x0001, revid=0x01
bus=0, slot=1, func=0
class=00-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0xff (7650 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=1
found-> vendor=0x8086, dev=0x0482, revid=0x03
bus=0, slot=2, func=0
class=00-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0xf8 (7440 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
de0: <Digital 21040 Ethernet> port 0x10100-0x1017f mem 0x81000100-0x8100017f irq 2 at device 0.0 on pci0
de0: Reserved 0x80 bytes for rid 0x14 type 3 at 0x81000100
de0: interrupting at T2 irq 2 (stdio irq 2)
de0: [GIANT-LOCKED]
de0: DEC 21040 [10Mb/s] pass 2.3
de0: bpf attached
de0: Ethernet address: 08:00:2b:e2:78:1c
sym0: <810> port 0x10000-0x100ff mem 0x81000000-0x810000ff irq 1 at device 1.0 on pci0
sym0: Reserved 0x100 bytes for rid 0x14 type 3 at 0x81000000
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: open drain IRQ line driver
sym0: using NCR-generic firmware.
sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/00/00/00/00/00
sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 03/c8/00/00/08/00
sym0: Delay (GEN=11): 252 msec, 35271 KHz
sym0: Delay (GEN=11): 283 msec, 31407 KHz
sym0: Delay (GEN=11): 282 msec, 31518 KHz
sym0: interrupting at T2 irq 1 (stdio irq 1)
sym0: [GIANT-LOCKED]
eisab0: <PCI-EISA bridge> at device 2.0 on pci0
eisa0: <EISA bus> on eisab0
mainboard0: <DEC2a01 (System Board)> on eisa0 slot 0
eisa0: unknown card CPQ3111 (0x0e113111) at slot 2
isa0: <ISA bus> on eisab0
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROM> at iomem 0xc0000-0xc67ff on isa0
ata0 at port 0x3f6,0x1f0-0x1f7 irq 14 on isa0
ata0: reset tp1 mask=00 ostat0=ff ostat1=ff
ata0: interrupting at T2 irq 14 (stdio irq 21)
ata0: [MPSAFE]
ata1 at port 0x376,0x170-0x177 irq 15 on isa0
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ata1: interrupting at T2 irq 15 (stdio irq 22)
ata1: [MPSAFE]
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0: atkbd0, generic (0), config:0x0, flags:0x1f0000
atkbd0: interrupting at T2 irq 1 (stdio irq 6)
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0061
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: interrupting at T2 irq 6 (stdio irq 7)
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
Calibrating clock(s) ... PCC clock: 249772724 Hz (firmware 250000000 Hz)
i8254 clock: 1193176 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Polled port
ppi0: <Parallel I/O> on ppbus0
ppc0: interrupting at T2 irq 7 (stdio irq 9)
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x0>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x201 0x211 0x201 0x201
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio0: interrupting at T2 irq 4 (stdio irq 15)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x201 0x201 0x201 0x201
sio1 at port 0x2f8-0x2ff irq 3 flags 0x80 on isa0
sio1: type 16550A
sio1: interrupting at T2 irq 3 (stdio irq 8)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xb8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
isa_probe_children: probing PnP devices
procfs registered
Timecounter "i8254" frequency 1193182 Hz quality 0
Timecounters tick every 0.976 msec
lo0: bpf attached
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xfffffc00009c63d8
GEOM: Configure md0a, start 8192 length 4415488 end 4423679
GEOM: Configure md0c, start 0 length 4423680 end 4423679
de0: enabling 10baseT port
(probe6:sym0:0:6:0): Retrying Command
(probe0:sym0:0:0:0): Retrying Command
(probe1:sym0:0:1:0): Retrying Command
(probe2:sym0:0:2:0): Retrying Command
(probe3:sym0:0:3:0): Retrying Command
(probe6:sym0:0:6:0): error 22
(probe6:sym0:0:6:0): Unretryable Error
pass0 at sym0 bus 0 target 0 lun 0
pass0: <DEC RZ28 (C) DEC 442D> Fixed Direct Access SCSI-2 device
pass0: Serial Number PCB=ZG50902578 ; HDA=000051261444
pass0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
pass1 at sym0 bus 0 target 1 lun 0
pass1: <DEC RZ28 (C) DEC D41C> Fixed Direct Access SCSI-2 device
pass1: Serial Number PCB=419250460827(ZG50460827 ?); HDA=0000000050452327
pass1: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
pass2 at sym0 bus 0 target 2 lun 0
pass2: <DEC RZ28 (C) DEC 442D> Fixed Direct Access SCSI-2 device
pass2: Serial Number PCB=ZG50901887 ; HDA=000051258040
pass2: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
pass3 at sym0 bus 0 target 3 lun 0
pass3: <DEC RZ28 (C) DEC 442D> Fixed Direct Access SCSI-2 device
pass3: Serial Number PCB=ZG50891425 ; HDA=000051261132
pass3: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
pass4 at sym0 bus 0 target 6 lun 0
pass4: <DEC RRD43 (C) DEC 1084> Removable CD-ROM SCSI-2 device
pass4: 4.166MB/s transfers (4.166MHz, offset 8)
cd0 at sym0 bus 0 target 6 lun 0
cd0: <DEC RRD43 (C) DEC 1084> Removable CD-ROM SCSI-2 device
cd0: 4.166MB/s transfers (4.166MHz, offset 8)
cd0: cd present [565180 x 512 byte records]
da0 at sym0 bus 0 target 0 lun 0
da0: <DEC RZ28 (C) DEC 442D> Fixed Direct Access SCSI-2 device
da0: Serial Number PCB=ZG50902578 ; HDA=000051261444
da0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
da0: 2007MB (4110480 512 byte sectors: 255H 63S/T 255C)
da1 at sym0 bus 0 target 1 lun 0
da1: <DEC RZ28 (C) DEC D41C> Fixed Direct Access SCSI-2 device
da1: Serial Number PCB=419250460827(ZG50460827 ?); HDA=0000000050452327
da1: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
da1: 2007MB (4110480 512 byte sectors: 255H 63S/T 255C)
da2 at sym0 bus 0 target 2 lun 0
da2: <DEC RZ28 (C) DEC 442D> Fixed Direct Access SCSI-2 device
da2: Serial Number PCB=ZG50901887 ; HDA=000051258040
da2: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
da2: 2007MB (4110480 512 byte sectors: 255H 63S/T 255C)
da3 at sym0 bus 0 target 3 lun 0
da3: <DEC RZ28 (C) DEC 442D> Fixed Direct Access SCSI-2 device
da3: Serial Number PCB=ZG50891425 ; HDA=000051261132
da3: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
da3: 2007MB (4110480 512 byte sectors: 255H 63S/T 255C)
GEOM: new disk cd0
GEOM: new disk da0
GEOM: new disk da1
GEOM: new disk da2
GEOM: new disk da3
release_aps: releasing secondary CPUs
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
GEOM: Configure da0a, start 6190080 length 6190080 end 12380159
GEOM: Configure da0b, start 12380160 length 136181760 end 148561919
GEOM: Configure da0c, start 0 length 2102563840 end 2102563839
GEOM: Configure da0d, start 148561920 length 1954001920 end 2102563839
GEOM: Configure da1a, start 0 length 100663296 end 100663295
GEOM: Configure da1b, start 100663296 length 536870912 end 637534207
GEOM: Configure da1c, start 0 length 2104565760 end 2104565759
GEOM: Configure da1e, start 637534208 length 1467031552 end 2104565759
GEOM: Configure da2a, start 0 length 2102563840 end 2102563839
GEOM: Configure da2c, start 0 length 2102563840 end 2102563839
GEOM: Configure da3a, start 0 length 2102563840 end 2102563839
GEOM: Configure da3c, start 0 length 2102563840 end 2102563839
Mounting root from ufs:/dev/md0
WARNING: clock gained 7 days -- CHECK AND RESET THE DATE!
start_init: trying /sbin/init
start_init: trying /sbin/oinit
start_init: trying /sbin/init.bak
start_init: trying /stand/sysinstall
/stand/sysinstall running as init on serial console
These are the predefined terminal types available to
sysinstall when running stand-alone. Please choose the
closest match for your particular terminal.
===
More information about the freebsd-alpha
mailing list