Power OFF button on very old motherboard with FreeBSD 7.2

[newuse at qip.ru]

Hallow, I am new in any mailing lists and I unfortunately don't know how to post as a followup :((
But ther is an error in dump:
# acpidump -t
acpidump: Can't find ACPI information

I think it is because the dump is not supported by my kernel :(


On Friday 30 April 2010 2:22:09 pm newuse at qip.ru wrote:
> Can you try booting with 'hint.apic.0.disabled=1' set in loader.conf?  Also, 
> if you could obtain a full dmesg that would be helpful.

Can you please get the output of acpidump -t and post it to the mailing list 
as a followup?

> -- 
> John Baldwin
> 
> Thank you, I add "hint.apic.0.disabled=1" (without "") to the end of  
loader.conf, now it looks like:
> acpi_load="YES"
> apm_load="YES"
> alias_ftp_load="YES"
> hint.apic.0.disabled=1
> 
> my fulll DMESG:
> # dmesg
> Copyright (c) 1992-2009 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 7.2-RELEASE #10: Thu Mar 25 05:42:27 MSK 2010
>     root at NewUse.vesnet.net:/usr/obj/usr/src/sys/MYKNL
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Pentium II/Pentium II Xeon/Celeron (350.80-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0x652  Stepping = 2
>   Features=0x183f9ff
> real memory  = 134217728 (128 MB)
> avail memory = 121806848 (116 MB)
> kbd1 at kbdmux0
> ACPI Error (tbxfroot-0308): A valid RSDP was not found [20070320]
> ACPI: Table initialisation failed: AE_NOT_FOUND
> ACPI: Try disabling either ACPI or apic support.
> pcib0:  pcibus 0 on motherboard
> pir0:  on motherboard
> pci0:  on pcib0
> agp0:  on hostb0
> pcib1:  at device 1.0 on pci0
> pci1:  on pcib1
> isab0:  at device 7.0 on pci0
> isa0:  on isab0
> atapci0:  port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 
7.1 on pci0
> ata0:  on atapci0
> ata0: [ITHREAD]
> ata1:  on atapci0
> ata1: [ITHREAD]
> uhci0:  port 0xde00-0xde1f irq 11 at device 7.2 on pci0
> uhci0: [GIANT-LOCKED]
> uhci0: [ITHREAD]
> usb0:  on uhci0
> usb0: USB revision 1.0
> uhub0:  on usb0
> uhub0: 2 ports with 2 removable, self powered
> intsmb0:  port 0x440-0x44f at device 7.3 on pci0
> intsmb0: intr IRQ 9 enabled revision 0
> intsmb0: [GIANT-LOCKED]
> intsmb0: [ITHREAD]
> intsmb0: PM I/O mapped 400
> smbus0:  on intsmb0
> smb0:  on smbus0
> pcm0:  port 0xdc00-0xdc3f irq 11 at device 14.0 on pci0
> pcm0: 
> pcm0: [ITHREAD]
> pcm0: 
> rl0:  port 0xda00-0xdaff mem 0xefffbf00-0xefffbfff irq 10 at device 16.0 on 
pci0
> miibus0:  on rl0
> rlphy0:  PHY 0 on miibus0
> rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> rl0: Ethernet address: 00:80:48:38:3a:3d
> rl0: [ITHREAD]
> rl1:  port 0xd800-0xd8ff mem 0xefffbe00-0xefffbeff irq 9 at device 18.0 on 
pci0
> miibus1:  on rl1
> rlphy1:  PHY 0 on miibus1
> rlphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> rl1: Ethernet address: 00:18:e7:09:0f:09
> rl1: [ITHREAD]
> rl2:  port 0xd600-0xd6ff mem 0xefffbd00-0xefffbdff irq 11 at device 20.0 on 
pci0
> miibus2:  on rl2
> rlphy2:  PHY 0 on miibus2
> rlphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> rl2: Ethernet address: 00:11:95:5b:8e:7a
> rl2: [ITHREAD]
> cpu0 on motherboard
> pmtimer0 on isa0
> atkbdc0:  at port 0x60,0x64 on isa0
> atkbd0:  irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> atkbd0: [ITHREAD]
> fdc0:  at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> fdc0: [FILTER]
> fd0:
> 

-- 
John Baldwin