cvs commit: src/sys/dev/bfe if_bfe.c if_bfereg.h

Pyun YongHyeon yongari at FreeBSD.org
Fri Aug 29 01:48:39 UTC 2008


yongari     2008-08-29 01:48:22 UTC

  FreeBSD src repository

  Modified files:        (Branch: RELENG_6)
    sys/dev/bfe          if_bfe.c if_bfereg.h 
  Log:
  SVN rev 182426 on 2008-08-29 01:48:22Z by yongari
  
  MFC r181953:
     o Sort includes and add <endian.h> to support endianness.
     o Removed unneeded header files.
     o bus_dma(9) fix:
       - created parent tag with 1GB dma address limit with no
         alignment restrictions.
       - set 4096 alignment limit for Tx/Rx descriptor rings.
       - separate Rx buffer tag from Tx buffer tag such that Tx tag
         allows up-to 16 segments while Rx buffer tag only allows
         single segment.
       - it seems the controller has no alignment restrictions on Tx/Rx
         buffers. Remove ETHER_ALIGN alignment restriction in Tx/Rx
         buffers.
       - created a spare Rx dma map which would be used to cope with
         failure of loading a dma map.
       - make sure to load full Tx/Rx descriptor size for Tx/Rx
         descriptor dma maps, previously bfe(4) used to load single
         descriptor size for each descriptor rings. I have no idea how
         it could be run without problems.
       - don't blindly cast bus_addr_t type to 32bits in bfe_dma_map().
       - created bfe_dma_free() to free allocated dma memory/tags.
       - make sure to invoke bus_dmamap_sync(9) before/after processing
         descriptor rings/buffers. Because the hardware has severe dma
         address space limitation, bounce-buffers would be always used
         on systems with more than 1GB memory during
         descriptors/buffers access.
       - added Tx descriptor ring initialization function,
         bfe_list_tx_init().
       - moved producer/consumer index initialization to
         bfe_list_tx_init() and bfe_list_rx_init() from
         bfe_chip_reset().
       - added bfe_discard_buf() which will update loaded descriptors
         without unloading/reloading the dma map to speed up error
         recovery.
       - implemented Tx side bus_dmamap_load_mbuf_sg(9). The number of
         segments allowed was chosen to be 16 which should be enough for
         non-TSO capable hardwares. Setting SOF bit of Tx descriptor is
         done in the last to avoid potential race.
       - don't give up sending frames in bfe_start() until the hardware
         lacks free descriptors.
       - added XXX comment to second kick command and possible workaround.
       - implemented Rx side bus_dmamap_load_mbuf_sg(9).
       - removed bfe_dma_map_desc() as it's not needed anymore after
         the conversion to bus_dmamap_load_mbuf_sg(9).
       - added endianness support. With this change bfe(4) should work
         on any architectures that can create bounce buffers within 1GB
         address range.
       - add missing bus_dmamap_sync() in bfe_tx_eof()/bfe_rx_eof().
     o Use PCI_BAR instead of hardcoded value to set BARs.
       Simplified register access with bus_write_4(9)/bus_read_4(9) and
       removed bfe_btag, bfe_bhandle, bfe_vhandle in softc as it's not
       used anymore.
     o Reorder device detach logic such that bfe_detach() is also used
       for handling driver attach failure case.
     o Remove unnecessary KASSERT in bfe_detach().
     o Remove bfe_rx_cnt, bfe_up, bfe_vpd_prodname, bfe_vpd_readonly in
       softc.  It's not used at all.
     o Remove BFE_RX_RING_SIZE/BFE_RX_RING_SIZE/BFE_LINK_DOWN.
  
  Revision   Changes    Path
  1.25.2.14  +479 -354  src/sys/dev/bfe/if_bfe.c
  1.7.2.4    +20 -17    src/sys/dev/bfe/if_bfereg.h


More information about the cvs-src mailing list