cvs commit: src/sys/dev/ata ata-all.h ata-chipset.c ata-dma.c

Sun Apr 8 22:00:07 UTC 2007

On 2007.04.08 19:18:51 +0000, Søren Schmidt wrote:
> sos         2007-04-08 19:18:51 UTC
> 
>   FreeBSD src repository
> 
>   Modified files:
>     sys/dev/ata          ata-all.h ata-chipset.c ata-dma.c 
>   Log:
>   Hopefully unbreak the 64bit DMA support this time.

Now things work a bit more than before.  While I can now mount the
root file system on sledge.FreeBSD.org (SMP amd64 with 8GB RAM) I get
various write errors shortly after mounting root like:

ad0: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=4415
ad0: TIMEOUT - WRITE_DMA retrying (0 retries left) LBA=4415
ad0: FAILURE - WRITE_DMA timed out LBA=4415
g_vfs_done():ad0s1a[WRITE(offset=2228224, length=2048)]error = 5

When booting on kernel from: "Fri Apr 6 14:23:30 UTC 2007" it works
fine.

When I bring sys/dev/ata back to '2007/04/06 14:00:00' it can boot
normally again.

Working config:

[simon at sledge:~] ident /boot/kernel/kernel | grep ata
     $FreeBSD: src/sys/dev/ata/ata-all.c,v 1.279 2007/02/23 16:25:08 jhb Exp $
     $FreeBSD: src/sys/dev/ata/ata-chipset.c,v 1.192 2007/03/12 15:34:08 sos Exp $
     $FreeBSD: src/sys/dev/ata/ata-disk.c,v 1.201 2007/02/21 19:07:18 sos Exp $
     $FreeBSD: src/sys/dev/ata/ata-dma.c,v 1.143 2007/02/21 19:07:18 sos Exp $
     $FreeBSD: src/sys/dev/ata/ata-isa.c,v 1.31 2007/02/21 19:07:18 sos Exp $
     $FreeBSD: src/sys/dev/ata/ata-lowlevel.c,v 1.78 2007/02/21 19:07:18 sos Exp $
     $FreeBSD: src/sys/dev/ata/ata-pci.c,v 1.121 2007/02/23 12:18:33 piso Exp $
     $FreeBSD: src/sys/dev/ata/ata-queue.c,v 1.69 2007/03/13 20:31:56 thomas Exp $

dmesg:

Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-CURRENT #951: Sun Apr  8 20:23:09 UTC 2007
    simon at sledge.freebsd.org:/h/src/sys/amd64/compile/SLEDGE
ACPI APIC Table: <PTLTD          APIC  >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Opteron(tm) Processor 244 (1804.10-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0xf51  Stepping = 1
  Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
  AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow!+,3DNow!>
usable memory = 8514306048 (8119 MB)
avail memory  = 8250753024 (7868 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ACPI: RSDP @ 0x0xf6cb0/0x0024 (v  2 PTLTD )
ACPI: XSDT @ 0x0xfbf7388b/0x003C (v  1 PTLTD     XSDT   0x06040000  LTP 0x00000000)
ACPI: FACP @ 0x0xfbf75d7e/0x00F4 (v  3 AMD    HAMMER   0x06040000 PTEC 0x000F4240)
ACPI: DSDT @ 0x0xfbf738c7/0x2443 (v  1 AMD-K8  AMDACPI 0x06040000 MSFT 0x0100000E)
ACPI: FACS @ 0x0xfbf7ffc0/0x0040
ACPI: SRAT @ 0x0xfbf75e72/0x0118 (v  1 AMD    HAMMER   0x06040000 AMD  0x00000001)
ACPI: APIC @ 0x0xfbf75f8a/0x0076 (v  1 PTLTD     APIC   0x06040000  LTP 0x00000000)
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-27 on motherboard
ioapic2 <Version 1.1> irqs 28-31 on motherboard
acpi0: <PTLTD    XSDT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
unknown: I/O range not supported
unknown: I/O range not supported
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, fbf00000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x8000-0x807f,0x8080-0x80ff iomem 0xd8000-0xdbfff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci1: <ACPI PCI bus> on pcib1
ohci0: <OHCI (generic) USB controller> mem 0xfc100000-0xfc100fff irq 19 at device 0.0 on pci1
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xfc101000-0xfc101fff irq 19 at device 0.1 on pci1
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 3 ports with 3 removable, self powered
vgapci0: <VGA-compatible display> port 0x2000-0x20ff mem 0xfd000000-0xfdffffff,0xfc102000-0xfc102fff irq 18 at device 6.0 on pci1
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 8111 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1020-0x102f at device 7.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <bridge> at device 7.3 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pci2:3:0: bad VPD cksum, remain 14
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x1002> mem 0xfe000000-0xfe00ffff irq 27 at device 3.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge0: Ethernet address: 00:50:45:00:aa:a2
bge0: [ITHREAD]
pci2:4:0: bad VPD cksum, remain 14
bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x1002> mem 0xfe010000-0xfe01ffff irq 27 at device 4.0 on pci2
miibus1: <MII bus> on bge1
brgphy1: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge1: Ethernet address: 00:50:45:00:aa:a3
bge1: [ITHREAD]
pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci3: <ACPI PCI bus> on pcib3
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A, console
sio0: [FILTER]
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff,0xc9800-0xcafff,0xdc000-0xdffff on isa0
ppc0: cannot reserve I/O port range
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
ad0: 38166MB <Seagate ST340014A 3.54> at ata0-master UDMA100
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad0s1a
Loading configuration files.
kernel dumps on /dev/ad0s1b
Entropy harvesting: interrupts ethernet point_to_point kickstart.
swapon: adding /dev/ad0s1b as swap device
Starting file system checks:
/dev/ad0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1a: clean, 62047 free (831 frags, 7652 blocks, 0.7% fragmentation)
/dev/ad0s1d: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1d: clean, 1597566 free (14894 frags, 197834 blocks, 0.7% fragmentation)
/dev/ad0s1e: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1e: clean, 234781 free (421 frags, 29295 blocks, 0.2% fragmentation)
/dev/ad0s1f: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1f: clean, 253807 free (31 frags, 31722 blocks, 0.0% fragmentation)
/dev/ad0s1g: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1g: clean, 1046697 free (400161 frags, 80817 blocks, 3.4% fragmentation)
ad0: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=4415
ad0: TIMEOUT - WRITE_DMA retrying (0 retries left) LBA=4415
ad0: FAILURE - WRITE_DMA timed out LBA=4415
g_vfs_done():ad0s1a[WRITE(offset=2228224, length=2048)]error = 5
mount:  : Input/output error
Mounting root filesystem rw failed, startup aborted
Boot interrupted
Enter full pathname of shell or RETURN for /bin/sh: ad0: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=4415
ad0: TIMEOUT - WRITE_DMA retrying (0 retries left) LBA=4415
ad0: FAILURE - WRITE_DMA timed out LBA=4415
g_vfs_done():ad0s1a[WRITE(offset=2228224, length=2048)]error = 5
ad0: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=4415
ad0: TIMEOUT - WRITE_DMA retrying (0 retries left) LBA=4415
ad0: FAILURE - WRITE_DMA timed out LBA=4415

-- 
Simon L. Nielsen