Weird problem

Thu May 17 01:22:38 PDT 2001

Hello,

On Thu, 17 May 2001, I wrote:

> > Does the driver report any messages to the console?  If so, run with
> > "aic7xxx=verbose" and send me the messages.  You may need to setup a
> > serial console to acurately capture the messages.
> 
> The output from different tries was different every time:

Well, I forgot to send you typical boot-up messages, just in case they are
interesting. See below.

Regards,
  Metod

Metod Kozelj

mailto:Metod.Kozelj at rzs-hm.si            /\  Ne posiljajte mi smeti ker grizem!
http://www.rzs-hm.si/                   /  \  Don't spam me for I bite!
_______________________________________/    \__________________________________

---- perl -e 'print $i=pack(c5,(41*2),sqrt(7056),(unpack(c,H)-2),oct(115),10);'

-----------------------

Linux version 2.4.4 (metodk at fractus) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #2 Thu May 17 07:22:46 CEST 2001
Booting on EB164 variation SX164 using machine vector SX164 from SRM
Command line: root=/dev/sda4 console=ttyS0 aic7xxx=verbose
memcluster 0, usage 1, start        0, end      256
memcluster 1, usage 0, start      256, end    16374
memcluster 2, usage 1, start    16374, end    16384
freeing pages 256:1024
freeing pages 1288:16374
PCA56 MVI set enabled
pci: cia revision 1 (pyxis)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/sda4 console=ttyS0 aic7xxx=verbose
Using epoch = 1952
Console: colour VGA+ 80x25
Calibrating delay loop... 1057.24 BogoMIPS
Memory: 124616k/130992k available (1178k kernel code, 4328k reserved, 289k data, 256k init)
Dentry-cache hash table entries: 16384 (order: 5, 262144 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 8192 bytes)
Page-cache hash table entries: 16384 (order: 4, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 131072 bytes)
VFS: Diskquotas version dquot_6.4.0 initialized
POSIX conformance testing by UNIFIX
pci: passed tb register update test
pci: passed sg loopback i/o read test
pci: passed tbia test
pci: passed pte write cache snoop test
pci: failed valid tag invalid pte reload test (mcheck; workaround available)
pci: passed pci machine check test
  got res[8000:80ff] for resource 0 of Adaptec AIC-7881U
  got res[8400:847f] for resource 0 of 3Com Corporation 3c905B 100BaseTX [Cyclone]
  got res[8480:848f] for resource 4 of Contaq Microsystems 82c693 (#2)
  got res[9000000:9ffffff] for resource 0 of Matrox Graphics, Inc. MGA 2164W [Millennium II]
  got res[a000000:a7fffff] for resource 2 of Matrox Graphics, Inc. MGA 2164W [Millennium II]
  got res[a800000:a81ffff] for resource 6 of 3Com Corporation 3c905B 100BaseTX [Cyclone]
  got res[a820000:a82ffff] for resource 6 of Matrox Graphics, Inc. MGA 2164W [Millennium II]
  got res[a830000:a83ffff] for resource 6 of Adaptec AIC-7881U
  got res[a840000:a84ffff] for resource 4 of Contaq Microsystems 82c693 (#3)
  got res[a850000:a853fff] for resource 1 of Matrox Graphics, Inc. MGA 2164W [Millennium II]
  got res[a854000:a854fff] for resource 1 of Adaptec AIC-7881U
  got res[a855000:a855fff] for resource 0 of Contaq Microsystems 82c693 (#4)
  got res[a856000:a85607f] for resource 1 of 3Com Corporation 3c905B 100BaseTX [Cyclone]
PCI enable device: (Matrox Graphics, Inc. MGA 2164W [Millennium II])
  cmd reg 0x7
PCI enable device: (Adaptec AIC-7881U)
  cmd reg 0x7
PCI enable device: (Contaq Microsystems 82c693)
  cmd reg 0x7
PCI enable device: (Contaq Microsystems 82c693 (#2))
  cmd reg 0x5
PCI enable device: (Contaq Microsystems 82c693 (#3))
  cmd reg 0x7
PCI enable device: (Contaq Microsystems 82c693 (#4))
  cmd reg 0x6
PCI enable device: (3Com Corporation 3c905B 100BaseTX [Cyclone])
  cmd reg 0x7
SMC37c669 Super I/O Controller found @ 0x3f0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 82560kB/27520kB, 256 slots per queue
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
CY82C693: IDE controller on PCI bus 00 dev 41
CY82C693: chipset revision 0
CY82C693: not 100% native mode: will probe irqs later
CY82C693U driver v0.34 99-13-12 Andreas S. Krebs (akrebs at altavista.net)
    ide0: BM-DMA at 0x8480-0x8487, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0x8488-0x848f, BIOS settings: hdc:DMA, hdd:DMA
hda: FUJITSU MPD3043AT, ATA DISK drive
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hdc: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 8448300 sectors (4326 MB) w/512KiB Cache, CHS=8940/15/63, (U)DMA
Partition check:
 hda: hda1 hda2 hda3 hda8
Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
rtc: Digital UNIX epoch (1952) detected
Real Time Clock Driver v1.10d
SCSI subsystem driver Revision: 1.00
ahc_pci:0:6:0: Reading SEEPROM...done.
ahc_pci:0:6:0: internal 50 cable is present, internal 68 cable is present
ahc_pci:0:6:0: external cable not present
ahc_pci:0:6:0: BIOS eeprom is present
ahc_pci:0:6:0: High byte termination Enabled
ahc_pci:0:6:0: Downloading Sequencer Program... 436 instructions downloaded
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.1.13
        <Adaptec 2940 Ultra SCSI adapter>
        aic7880: Ultra Wide Channel A, SCSI Id=7, 16/255 SCBs

  Vendor: SEAGATE   Model: ST34572N          Rev: 0784
  Type:   Direct-Access                      ANSI SCSI revision: 02
  Vendor: DEC       Model: RZ28D    (C) DEC  Rev: 0008
  Type:   Direct-Access                      ANSI SCSI revision: 02
  Vendor: NEC       Model: CD-ROM DRIVE:465  Rev: 1.03
  Type:   CD-ROM                             ANSI SCSI revision: 02
(scsi0:A:0): 3.300MB/s transfers
scsi0:0:0:0: Tagged Queuing enabled.  Depth 253
(scsi0:A:1): 3.300MB/s transfers
scsi0:0:1:0: Tagged Queuing enabled.  Depth 253
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
(scsi0:A:0:0): Sending SDTR period c, offset f
(scsi0:A:0:0): Received SDTR period c, offset f
	Filtered to period c, offset f
(scsi0:A:0): 20.000MB/s transfers (20.000MHz, offset 15)
scsi0: target 0 synchronous at 20.0MHz, offset = 0xf
(scsi0:A:0:0): Sending SDTR period c, offset f
(scsi0:A:0:0): Received SDTR period c, offset f
	Filtered to period c, offset f
SCSI device sda: 8888924 512-byte hdwr sectors (4551 MB)
 sda: sda1 sda2 sda3 sda4 sda5
(scsi0:A:1:0): Sending WDTR 1
(scsi0:A:1:0): Received WDTR 1 filtered to 1
(scsi0:A:1): 6.600MB/s transfers (16bit)
scsi0: target 1 using 16bit transfers
(scsi0:A:1:0): Sending SDTR period c, offset 8
(scsi0:A:1:0): Received SDTR period 19, offset 8
	Filtered to period 19, offset 8
(scsi0:A:1): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
scsi0: target 1 synchronous at 10.0MHz, offset = 0x8
(scsi0:A:1:0): Sending WDTR 1
(scsi0:A:1:0): Received WDTR 1 filtered to 1
(scsi0:A:1): 6.600MB/s transfers (16bit)
scsi0: target 1 using asynchronous transfers
(scsi0:A:1:0): Sending SDTR period 19, offset 8
(scsi0:A:1:0): Received SDTR period 19, offset 8
	Filtered to period 19, offset 8
(scsi0:A:1): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
scsi0: target 1 synchronous at 10.0MHz, offset = 0x8
SCSI device sdb: 4110480 512-byte hdwr sectors (2105 MB)
 sdb: sdb1 sdb3 sdb8
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 256k freed
Adding Swap: 270992k swap-space (priority 10)
Adding Swap: 118864k swap-space (priority 5)
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
SB 4.13 detected OK (220)
<Sound Blaster 16 (4.13)> at 0x220 irq 10 dma 1,5
<Sound Blaster 16> at 0x330 irq 10 dma 0,0
3c59x.c:LK1.1.13 27 Jan 2001  Donald Becker and others. http://www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
eth0: 3Com PCI 3c905B Cyclone 100baseTx at 0x8400,  00:50:04:66:df:0b, IRQ 24
  product code 544e rev 00.9 date 02-10-99
  8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
  MII transceiver found at address 24, status 782d.
  Enabling bus-master transmits and whole-frame receives.
eth0: scatter/gather enabled. h/w checksums enabled
eth0: using NWAY device table, not 8
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).

To Unsubscribe: send mail to majordomo at FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message