2940U2W under Linux 2.4.x

Larry Battraw battraw at home.com
Thu Aug 16 18:26:42 PDT 2001


Here's 2.4.8 with the 6.2.1 patches (there were no rejects when applying 
the patch although it was for 2.4.7).

Larry


>>The messages provided are the for the versions shipped with the kernels. 
>> Would it be useful to patch to 6.2.1 and send on the logs?
>>
> 
> Yes.
> 
> --
> Justin
> 
> To Unsubscribe: send mail to majordomo at FreeBSD.org
> with "unsubscribe aic7xxx" in the body of the message
> 
> 


-------------- next part --------------
Linux version 2.4.8 (root at rambo.home.com) (gcc version 2.95.3 20010315 (release)) #3 Thu Aug 16 17:40:28 MST 2001
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000ffec000 (usable)
 BIOS-e820: 000000000ffec000 - 000000000ffef000 (ACPI data)
 BIOS-e820: 000000000ffef000 - 000000000ffff000 (reserved)
 BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 65516
zone(0): 4096 pages.
zone(1): 61420 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=linux ro root=802 console=ttyS0,9600 console=ttyS0 aic_7xxx=verbose:0xffff
Initializing CPU#0
Detected 1208.772 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2411.72 BogoMIPS
Memory: 254776k/262064k available (1523k kernel code, 6900k reserved, 559k data, 200k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: AMD Athlon(tm) Processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xf1150, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:04.0
Applying VIA southbridge workaround.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
Starting kswapd v1.8
udf: registering filesystem
0x378: FIFO is 16 bytes
0x378: writeIntrThreshold is 8
0x378: readIntrThreshold is 8
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,COMPAT,ECP]
parport_pc: Via 686A parallel port: io=0x378
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
lp0: using parport0 (polling).
Real Time Clock Driver v1.10d
block: 128 slots per queue, batch=16
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
    ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio
PDC20265: IDE controller on PCI bus 00 dev 88
PCI: Found IRQ 10 for device 00:11.0
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
    ide2: BM-DMA at 0x7800-0x7807, BIOS settings: hde:DMA, hdf:pio
    ide3: BM-DMA at 0x7808-0x780f, BIOS settings: hdg:pio, hdh:pio
hda: YAMAHA CRW2100E, ATAPI CD/DVD-ROM drive
hdb: DVD-ROM BDV212B, ATAPI CD/DVD-ROM drive
hdc: Maxtor 91531U3, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hdc: 30015216 sectors (15368 MB) w/512KiB Cache, CHS=29777/16/63, UDMA(33)
Partition check:
 hdc: [PTBL] [1868/255/63] hdc1 hdc2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.18
PCI: Found IRQ 9 for device 00:0d.0
PCI: Sharing IRQ 9 with 00:04.2
PCI: Sharing IRQ 9 with 00:04.3
PCI: Sharing IRQ 9 with 00:09.0
PCI: Sharing IRQ 9 with 00:09.1
eth0: RealTek RTL8139 Fast Ethernet at 0xd0800000, 00:48:54:6b:86:15, IRQ 9
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: Detected Via Apollo Pro KT133 chipset
agpgart: AGP aperture is 64M @ 0xe4000000
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 5 for device 00:0a.0
Waiting List inconsistency. SCB index == 255, yet numscbs == 4.scsi0: Dumping Card State while idle, at SEQADDR 0x1a6
ACCUM = 0x0, SINDEX = 0x0, DINDEX = 0x0, ARG_2 = 0x7f
HCNT = 0x0
SCSISEQ = 0x12, SBLKCTL = 0xa
 DFCNTRL = 0x0, DFSTATUS = 0x89
LASTPHASE = 0x1, SCSISIGI = 0x0, SXFRCTL0 = 0x88
SSTAT0 = 0x0, SSTAT1 = 0x0
STACK == 0x0, 0x0, 0x0, 0x0
SCB count = 4
Kernel NEXTQSCB = 3
Card NEXTQSCB = 3
QINFIFO entries: 
Waiting Queue entries: 0:255 1:255 2:255 3:255 4:255 5:255 6:255 7:255 8:255 9:255 10:255 11:255 12:255 13:255 14:255 15:255 16:255 17:255 18:255 19:255 20:255 21:255 22:255 23:255 24:255 25:255 26:255 27:255 28:255 29:255 30:255 31:255 
Disconnected Queue entries: 0:255 1:255 2:255 3:255 4:255 5:255 6:255 7:255 8:255 9:255 10:255 11:255 12:255 13:255 14:255 15:255 16:255 17:255 18:255 19:255 20:255 21:255 22:255 23:255 24:255 25:255 26:255 27:255 28:255 29:255 30:255 31:255 
QOUTFIFO entries: 
Sequencer Free SCB List: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 
Pending list: 
Kernel Free SCB list: 2 1 0 
Kernel panic: for safety
scsi0: brkadrint, PCI Error detected at seqaddr = 0x1a6
scsi0: Dumping Card State while idle, at SEQADDR 0x1a6
ACCUM = 0x0, SINDEX = 0x0, DINDEX = 0x0, ARG_2 = 0x7f
HCNT = 0x0
SCSISEQ = 0x12, SBLKCTL = 0xa
 DFCNTRL = 0x0, DFSTATUS = 0x89
LASTPHASE = 0x1, SCSISIGI = 0x0, SXFRCTL0 = 0x88
SSTAT0 = 0x0, SSTAT1 = 0x0
STACK == 0x0, 0x0, 0x0, 0x0
SCB count = 4
Kernel NEXTQSCB = 3
Card NEXTQSCB = 3
QINFIFO entries: 
Waiting Queue entries: 0:255 1:255 2:255 3:255 4:255 5:255 6:255 7:255 8:255 9:255 10:255 11:255 12:255 13:255 14:255 15:255 16:255 17:255 18:255 19:255 20:255 21:255 22:255 23:255 24:255 25:255 26:255 27:255 28:255 29:255 30:255 31:255 
Disconnected Queue entries: 0:255 1:255 2:255 3:255 4:255 5:255 6:255 7:255 8:255 9:255 10:255 11:255 12:255 13:255 14:255 15:255 16:255 17:255 18:255 19:255 20:255 21:255 22:255 23:255 24:255 25:255 26:255 27:255 28:255 29:255 30:255 31:255 
QOUTFIFO entries: 
Sequencer Free SCB List: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 
Pending list: 
Kernel Free SCB list: 2 1 0 
Waiting List inconsistency. SCB index == 255, yet numscbs == 4.scsi0: Dumping Card State while idle, at SEQADDR 0x1a6
ACCUM = 0x0, SINDEX = 0x0, DINDEX = 0x0, ARG_2 = 0x7f
HCNT = 0x0
SCSISEQ = 0x12, SBLKCTL = 0xa
 DFCNTRL = 0x0, DFSTATUS = 0x89
LASTPHASE = 0x1, SCSISIGI = 0x0, SXFRCTL0 = 0x88
SSTAT0 = 0x0, SSTAT1 = 0x0
STACK == 0x0, 0x0, 0x0, 0x0
SCB count = 4
Kernel NEXTQSCB = 3
Card NEXTQSCB = 3
QINFIFO entries: 
Waiting Queue entries: 0:255 1:255 2:255 3:255 4:255 5:255 6:255 7:255 8:255 9:255 10:255 11:255 12:255 13:255 14:255 15:255 16:255 17:255 18:255 19:255 20:255 21:255 22:255 23:255 24:255 25:255 26:255 27:255 28:255 29:255 30:255 31:255 
Disconnected Queue entries: 0:255 1:255 2:255 3:255 4:255 5:255 6:255 7:255 8:255 9:255 10:255 11:255 12:255 13:255 14:255 15:255 16:255 17:255 18:255 19:255 20:255 21:255 22:255 23:255 24:255 25:255 26:255 27:255 28:255 29:255 30:255 31:255 
QOUTFIFO entries: 
Sequencer Free SCB List: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 
Pending list: 
Kernel Free SCB list: 2 1 0 
Kernel panic: for safety
In interrupt handler - not syncing


More information about the aic7xxx mailing list