Work on the 29160?
Mike Sharp
mike_sharp at pacbell.net
Thu Nov 2 09:24:44 PST 2000
Hi,
Is anyone out there working on changes to support the 29160 board?
It seems to work somewhat, but I'm seeing a few problems.
Any thoughts would be greatly appreciated.
1. With device disconnect enabled I get the following repeated
infinitely during boot:
No active SCB for reconnecting target - Issuing BUS DEVICE RESET
SAVED_TCL=0x1, ARG_1=0xff, SEQ_ADDR=0x11d
2. With device disconnet disabled I can get the system to boot, but
I can't run
at 160MB, only 40MB. The appropriate section of the boot log is
below.
In both cases the system in question only has a single 18Mb Seagate
Cheetah
attached to the 29160. Termination is not an issue.
--Mike
Nov 2 08:34:39 gueuze kernel: (scsi0) <Adaptec AIC-7892 Ultra 160/m
SCSI host adapter> found at PCI 0/14/0
Nov 2 08:34:39 gueuze kernel: (scsi0) Wide Channel, SCSI ID=7, 32/255
SCBs
Nov 2 08:34:39 gueuze kernel: (scsi0) Downloading sequencer code... 392
instructions downloaded
Nov 2 08:34:39 gueuze kernel: scsi0 : Adaptec AHA274x/284x/294x
(EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
Nov 2 08:34:39 gueuze kernel: <Adaptec AIC-7892 Ultra 160/m SCSI
host adapter>
Nov 2 08:34:39 gueuze kernel: scsi : 1 host.
Nov 2 08:34:39 gueuze kernel: (scsi0:0:0:0) Synchronous at 160.0
Mbyte/sec, offset 63.
Nov 2 08:34:39 gueuze kernel: scsi : aborting command due to timeout :
pid 0, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00
Nov 2 08:34:39 gueuze kernel: SCSI host 0 abort (pid 0) timed out -
resetting
Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0
channel 0.
Nov 2 08:34:39 gueuze kernel: (scsi0:0:0:0) Synchronous at 160.0
Mbyte/sec, offset 63.
Nov 2 08:34:39 gueuze kernel: SCSI host 0 abort (pid 0) timed out -
resetting
Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0
channel 0.
Nov 2 08:34:39 gueuze kernel: SCSI host 0 channel 0 reset (pid 0) timed
out - trying harder
Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0
channel 0.
Nov 2 08:34:39 gueuze kernel: (scsi0:0:0:0) Synchronous at 160.0
Mbyte/sec, offset 63.
Nov 2 08:34:39 gueuze kernel: SCSI host 0 abort (pid 0) timed out -
resetting
Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0
channel 0.
Nov 2 08:34:39 gueuze kernel: SCSI host 0 channel 0 reset (pid 0) timed
out - trying harder
Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0
channel 0.
Nov 2 08:34:39 gueuze kernel: (scsi0:0:0:0) Synchronous at 40.0
Mbyte/sec, offset 63.
Nov 2 08:34:39 gueuze kernel: SCSI host 0 abort (pid 0) timed out -
resetting
Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0
channel 0.
Nov 2 08:34:39 gueuze kernel: SCSI host 0 channel 0 reset (pid 0) timed
out - trying harder
Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0
channel 0.
Nov 2 08:34:39 gueuze kernel: Vendor: SEAGATE Model:
ST318404LW Rev: 3074
Nov 2 08:34:39 gueuze kernel: Type:
Direct-Access ANSI SCSI revision: 03
Nov 2 08:34:39 gueuze kernel: Detected scsi disk sda at scsi0, channel
0, id 0, lun 0
Nov 2 08:34:39 gueuze kernel: SCSI device sda: hdwr sector= 512 bytes.
Sectors= 35843670 [17501 MB] [17.5 GB]
Nov 2 08:34:39 gueuze kernel: sda: sda1 sda2 < sda5 sda6 sda7 >
To Unsubscribe: send mail to majordomo at FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message
More information about the aic7xxx
mailing list