Dell 410 Workstations and Asus Motherboard systems

[Juergen Hammelmann]

Hi, there all,

I have integrated the line, Doug has said, but there is no difference to
from before, it stops too, look down to the messages...

On a look at our motherboard, asus p2b-ls/350, I can find an
aic7890ab chip and an aic3860q chip, there are two ultrawide-connectors,
one is connected with the harddisc, an ultra2wide ibm,
and one 50-pin connector for narrow devices.

The "adaptec aic-7890 bios SCSISelect Utility v20107" shows me, you can
set host adapter termination, at the scsi device configuration section,
there you can't set any termination.

host adapter termination enabled oder disabled, there is no change 
in behaviour!

Juergen Hammelmann
---------------------------------------------------------------------------
...
aic7xxx: <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> at PCI 6/0
aic7xxx: Initial PCI_COMMAND value was 0x17
aic7xxx: Initial DEVCONFIG value was 0x540
aic7xxx: Loading serial EEPROM...done
aic7xxx: EEPROM is present.
aic7xxx: SE High byte termination Enabled
aic7xxx: SE Low byte termination Enabled
aic7xxx: LVD Low byte termination Enabled
aic7xxx: LVD High byte termination Enabled
(scsi0) <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> at PCI 6/0
(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi0) BIOS enabled, IO Port 0xd000, IRQ 10
(scsi0) IO Memory at 0xe0000000, MMAP Memory at 0x10805000
(scsi0) Resetting channel
(scsi0) Downloading sequencer code... 407 instructions downloaded
scsi0: Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.0pre5/3.2.4
      <Adaptec AIC-7890/1 Ultra2 SCSI host adapter>
scsi: 1 host.
(scsi0:0:-1:-1) Scanning channel for devices.
(scsi0:-1:-1:-1) Allocating initial 30 SCB structures.
(scsi0:0:0:0) Sending command 29/0x4 to QINFIFO
(scsi0:-1:-1:-1) Sending commands to QINFIFO
(scsi0:-1:-1:-1) Command complete Int.
(scsi0:0:0:0) Sending command 29/0x4 to QINFIFO
(scsi0:-1:-1:-1) Sending commands to QINFIFO
scsi: aborting command due to timeout: pid 1, scsi0, channel 0, id 0, lun
0 Inquiry 00 00 00 ff 00
aic7xxx driver version 5.1.0pre5/2.0.35
Controller type:
    Adaptec AIC-7890/1 Ultra2 SCSI host adapter
p->flags=0x904501, p->chip=0x406, p->features=0xf6, sequencer isn't paused
SIMODE0=0x0, SIMODE1=0xac, SSTAT0=0x0, SSTAT1=0x3, INTSTAT=0x0
SCSISIGI=0x44, SXFRCTL0=0x80,  SXFRCTL1=0x27, SCSISEQ=0x12, SEQCTL=0xb0
SCSIRATE=0x0, SCSIOFFSET=0, SEQADDR=0x61, LASTPHASE=P_DATAIN
(scsi0:0:0:0) dev_flags=0x21, WDTR:N/Y/Y, SDTR:N/N/N, q_depth=1:1:3
(scsi0:0:0:0) targ_scsirate=0x0, targ_offset=0
Timed out command is scb #29:
Tag29: flags=0x4, control=0x40, TCL=0x0, Sent
QINFIFO: (TAG)
Current SCB: (SCBPTR/TAG/CONTROL) 0/29/0x40
WAITING_SCBS: (SCBPTR/TAG/CONTROL) 255->
FREE_SCBS: (SCBPTR/TAG/CONTROL) 1->1/255/0x0 2/255/0x0 3/255/0x0 4/255/0x0
5/255/0x0 6/255/0x0 7/255/0x0 8/255/0x0 9/255/0x0 10/255/0x0 11/255/0x0
12/255/0x0 13/255/0x0 14/255/0x0 15/255/0x0 16/255/0x0 17/255/0x0
18/255/0x0 19/255/0x0 20/255/0x0 21/255/0x0 22/255/0x0 23/255/0x0
24/255/0x0 25/255/0x0 26/255/0x0 27/255/0x0 28/255/0x0 29/255/0x0
30/255/0x0 31/255/0x0



--------------------------------------------------------------------------
WWW:    http://www.mathematik.uni-stuttgart.de/~hammelje
EMail:  juergen at tunix.mathematik.uni-stuttgart.de
        hammelje at trick.informatik.uni-stuttgart.de
Privat: Jürgen Hammelmann, 
	Brühlstr. 6, 71157 Hildrizhausen
        Germany
Tel.:	07034 / 6 15 78



To Unsubscribe: send mail to majordomo at FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message